Youtube How To Start A Stihl Chainsaw

STIHL is one of the best chainsaw brands available in the market place today, so exist rest bodacious if you accept one. Starting a Stihl chainsaw is quite similar to how you lot start whatsoever other chainsaw from other brands. They ordinarily come with the same levers and switches- the choke, throttle, recoil starter, and more. Although some features may vary, even from one Stihl model to another, about of them have a priming seedling and, most probably, a decompression valve. Nonetheless, there are a few things that may differ between a Stihl and other chainsaws one of which is that near Stihl models have a switch for an on-off-run position. They have fabricated the starting procedure quite easy and simple by including all these into a single principal control lever located behind the handle.

To showtime your Stihl Chainsaw follow these steps:

Stride i: Check the Fuel Cap
Stride 2: Activate the Chain Brake
Stride iii: Remove the Bar Cover
Step iv: Press the Decompression Valve
Step five: Pump the Primer Valve
Step 6: Set up the Principal Control to the Cold Start Setting
Step seven: Place the Chainsaw on Firm, Level Ground
Stride 8: Concur the Chainsaw Down with Your Foot and Hand
Step ix: Pull the Starter Rope
Footstep 10: Set up the Chainsaw to Open the "Asphyxiate"
Step 11: Move the Primary Command to the Idle Setting
Step 12: Lift the Chainsaw Up
Stride 13: Release the Chain Brake
Footstep 14: Check the Chain Lubrication

Now, knowing how to start a STIHL chainsaw is a bit like shooting fish in a barrel as long as you acquire the correct steps. If you're new to operating a chainsaw by yourself, you may be a little anxious most starting your ain STIHL chainsaw for the outset time. All the same, there'south nothing to worry about, this article will provide a complete step by step guide on how you can start your STIHL chainsaw. So, if you are not sure virtually how to commencement your new Stihl chainsaw or you're merely curious, you're at the right place.

Contents

1 Things to Consider before Starting Your STIHL Chainsaw
two How to Start Your STIHL Chainsaw
- 2.one ● Step 1: Check the Fuel Cap
- 2.2 ● Pace 2: Actuate the Chain Brake
- 2.three ● Step 3: Remove the Bar Cover
- 2.iv ● Step four: Press the Decompression Valve
- 2.five ● Step 5: Pump the Primer Valve
- 2.6 ● Step half dozen: Set the Main Control to the Cold Start Setting
- ii.seven ● Step 7: Place the Chainsaw on Firm, Level Ground
- 2.8 ● Step eight: Concur the Chainsaw Downwardly with Your Foot and Hand
- 2.9 ● Step ix: Pull the Starter Rope
- 2.x ● Footstep 10: Set the Chainsaw to Open the "Choke"
- 2.eleven ● Stride 11: Motility the Main Command to the Idle Setting
- ii.12 ● Step 12: Lift the Chainsaw Upward
- 2.thirteen ● Step thirteen: Release the Chain Brake
- ii.14 ● Step fourteen: Check the Chain Lubrication

Things to Consider before Starting Your STIHL Chainsaw

Earlier you think of starting your Stihl chainsaw, in that location are some important details you should pay attention to, to avert any trouble.

Read the transmission: Always read the user manual. This manual contains crucial safety information also equally operating instructions that you may not know virtually.
Never drop outset: Never "drop" get-go your chainsaw. Throw-starting or drop-starting a chainsaw is a very unsafe position that makes it hard for you lot to control your tool.
Always wear protective clothing when using your chainsaw. Wearing safe goggles and gloves tin can be at a minimum, just hearing protection such as earmuffs, and a confront mask is highly recommended.
Rubber: Ever consider your surroundings before y'all use your chainsaw. Ensure that in that location are no people or objects in your manner. If anyone approaches you in the centre of running the chainsaw, you should engage the chain brake immediately.

How to Start Your STIHL Chainsaw

Stihl recommends starting a chainsaw from a sitting position, notwithstanding, it is also possible to start it on uneven ground, if using a different technique. The right procedure for starting your Stihl chainsaw also depends on the type of tool yous're using: a gas-powered or electrical tool. Don't forget to read your chainsaw transmission thoroughly to check for necessary data on how to operate the tool safely. Hither is a step to footstep procedure on how to offset your STIHL chainsaw:

● Step one: Check the Fuel Cap

If you're using a gas-powered chainsaw, you will demand to fuel it upward before using it. Also, y'all should make sure the fuel cap is tight and secured, and there shouldn't be any drips of fuel on the outer parts of the chainsaw. If perhaps you see any fuel on the outside of the chainsaw, wipe information technology away carefully with a rag.

● Step 2: Activate the Chain Restriction

The chain restriction should commencement exist activated by pushing it forrard before yous kickoff the chainsaw. For Stihl chainsaws, the concatenation brake is ordinarily located just in front of the handlebar, and all yous take to exercise is push button it frontwards. Activating information technology will keep the concatenation locked as a form of safety while you are starting the chainsaw, and until yous are set up to use the tool.

● Step 3: Remove the Bar Cover

Stihl chainsaws are often equipped with a encompass that goes over the chain and bar. Remove this encompass before starting your chainsaw. Past doing this, yous'll make your tool fix to employ once yous start it.

● Step four: Press the Decompression Valve

Only professional person-grade Stihl chainsaws have a decompression valve, so unless you accept one, you should skip this footstep. If yous have a professional-grade saw, simply press the decompression valve down, often located on the top of the chainsaw, abreast the starter rope.

● Stride 5: Pump the Primer Valve

A lot of Stihl models come with a primer valve which is located on the side of the chainsaw, near the handlebar. If your chainsaw happens to have 1, simply button it downwardly well-nigh iv times. At one side of the chainsaw, a pocket-sized, translucent plastic bubble is usually nowadays. This is the primer bulb, which is used to remove air from the fuel piping, to let information technology to flow freely to the carburetor. Pressing it a few times will permit the engine to start quicker.

● Step vi: Set the Master Control to the Cold Outset Setting

In that location's a throttle trigger lockout located on the side of the chainsaw, press and hold it with your pollex, and push the master control (located on the rear left of the chainsaw) downward as far as information technology can become. You should e'er do this each time you lot desire to apply your chainsaw.

The work of the master control lever is that it sets the idling speed and choke. So you should gear up this lever to the choke or common cold outset position. To do this, agree the handle and printing down on the throttle trigger lock, which is located on pinnacle of the handle, then apply your thumb to depress it. Next, pull the throttle in with your forefinger and move the main command lever down to the choke position. If maybe, yous have used the chainsaw recently, then you should turn it off for some minutes before yous utilize it again. You should likewise set the master control to the warm setting before y'all start.

● Footstep 7: Place the Chainsaw on House, Level Ground

Carefully place the chainsaw on a leveled surface, just ensure that the bar and chain don't brand contact with the surface. Stihl recommends starting the chainsaw from a sitting position. So identify the saw on level footing, and make sure in that location is no object touching the bar and chain. As mentioned before, Do Not "drop" get-go or "throw" offset your chainsaw as these positions are unsafe and won't allow you to command your tool well.

● Step viii: Concur the Chainsaw Downwardly with Your Foot and Mitt

Slip your right toe into the opening on the rear handle. At the same fourth dimension, printing downwardly on the front handle with your left or less dominant paw, wrapping your fingers effectually information technology tightly and locking with your elbow. This position will secure your chainsaw as y'all beginning it.

● Step 9: Pull the Starter Rope

Hold the handle of the starter rope and slowly pull information technology vertically until you tin experience some resistance. Next, pull the rope quickly several times until the chainsaw fires up briefly. Pull the rope upwards, making sure information technology is in a vertical position, and without allowing the rope to chafe confronting the fan housing. Too make sure you only grab the starter rope handle (not the rope itself), and never wrap the rope around your hand.

● Step x: Fix the Chainsaw to Open the "Choke"

Your chainsaw may fire upward just then die immediately. When this occurs, motion the master control up to the half throttle (warm offset) setting. For a chainsaw that was recently used, the master command should already exist at the warm start setting. Next, pull the starter rope again to fire the chainsaw. Utilize the same technique equally in step ix to a higher place, and take hold of the starter rope handle again, pulling information technology vertically. The engine of your chainsaw should burn again.

● Step 11: Move the Primary Control to the Idle Setting

One time your chainsaw is running, printing the throttle trigger briefly with your forefinger. When you practice this, the master control lever will move back to the normal idle setting. Remember that simply a slight touch of your finger volition get it done. This will keep your chainsaw running.

● Pace 12: Elevator the Chainsaw Up

Observe your surroundings ane more time to be sure that there are no people or objects in your way. Stand up up slowly and advisedly, property your chainsaw at the handlebar. And then carefully release the chain brake by pulling it dorsum towards yous. Once you take done this, your chainsaw should be ready for use.

● Step 13: Release the Chain Brake

You tin can release the chain restriction past pulling the handle towards yourself with your left paw. Try to not lose hold of the handlebar as yous do this. When you hear a click audio, it means the chain has been released and you can at present turn on the bar. This will releases the chain brake and permit the chain to rotate on the sprocket.

● Pace 14: Check the Chain Lubrication

As mentioned earlier, you lot should always check the chain lubrication before y'all start. Carry your saw and hold information technology up against a light-colored background, such as a piece of paper on the ground, then open the throttle fully. If some of the chain lubricants announced on the background, it ways you can start work with your chainsaw. Don't forget that your safety and that of others come first. Make sure you discover the necessary condom precautions before yous exercise annihilation. Good luck!

Source: https://www.gardentoolexpert.com/how-to-start-your-stihl-chainsaw/

Posted by: stainbrookmork1972.blogspot.com